A snowboard wall mount keeps your board off the floor and on display between rides or through the off-season. This guide covers which mount style is easiest on the board, where in your home to hang it, and whether the bindings come off. It also covers the drying and storage wax steps to do before the board goes up.
Hang the board on a padded mount that holds it near its top inserts. Take the bindings off, and pick a cool, dry room out of direct sun and away from radiators and heating vents. Before it goes up, wipe it dry, hot wax a thick storage coat over the base and edges, and leave that coat unscraped until the board comes down.
Check the wall for wires and pipes before you drill.
Which snowboard wall mount style is easiest on the board?

Our read: a vertical holder that grips the board near its top inserts on padded contact points is the gentlest of the common styles. It holds the board at a part built to carry hardware, and nothing presses into the base. A horizontal rack works too when its padded arms sit under the edges. A single hook that hangs the board by its bindings is the style we'd skip, because the board's whole weight then hangs off the binding screws and inserts.
On any vertical holder, look for padded contact points and an adjustable width, the two checks in the table's What to check column below. We carry the Capita Wall Mount Snowboard Holders in black, so check its listing for both before you buy. For a reference point, Union's product page for its own holder lists protective contact points against base and edge damage and an adjustable width to help avoid re-drilling the wall.
Before you drill, check that every point touching the board is padded.
Can a wall mount damage a board or make it lose camber?
Our read: a padded mount holding the board near its top inserts is unlikely to change its camber, and heat, sun and damp do far more harm to a stored board. On the wall, the board carries only its own weight on two contact points. A cambered board and a rocker board hang the same way, so there is no bindings-up or bindings-down rule to follow.
Whitelines' summer storage advice says to keep a stored board out of direct sunlight to avoid warping. Burton's storage guide warns against attics that reach 85°F (30°C) or more, basements that get damp, and spots that get long stretches of direct sun. Choose the wall for temperature and light first, then the mount.
Should the bindings stay on while the board hangs?
Take the bindings off before the board goes on the wall. Whitelines says to remove them for summer storage, both to check them for wear and cracks and to relieve the screws' pressure on the inserts. Write down your stance width and angles first. Then take the screws out fully rather than backing them off a turn. Keep the screws, washers and discs in a bag with the bindings so nothing goes missing by fall.
Where in your home should the board hang?
Put it in a room that stays cool and dry, out of direct sun, on a wall with no radiator or heating vent below it. Never Summer says to keep a board in a room that doesn't swing widely in temperature or climb above 85°F (about 30°C), and notes that garages are often too hot in summer. If your free wall is in the basement, pick one that stays dry. Look at a closet wall or a spare-room wall away from the window first.
How to prep the board before it goes up
Dry it, take the bindings off, and hot wax a thick storage coat that stays on until the board comes down.
- Wipe the base, topsheet and edges dry with a clean towel.
- Take the bindings off and bag the hardware.
- Hot wax a thick coat over the whole base, running it out over the edges.
- Let the wax cool and leave it unscraped.
- Put the board on the mount once the wax has set.
Never Summer says never to store a board while it is still wet, because the bindings and other hardware can rust. Burton's storage guide says not to scrape storage wax, because a snowboard base is porous and dries out when left for months. Whitelines says the storage coat should cover the whole base thickly and run over the edges to seal them against rust. The iron and scraping steps are in our guide to how to hot wax a snowboard.
Do I need a stud, or are drywall anchors enough?
Use a stud where one lines up with the spot you want, and use the wall plugs that come with the mount where none does. Union's holder ships with wall plugs, and its listed tools are a drill, a 4 mm drill bit, a tape measure, a level and a screwdriver. Union's install steps have the board rest near its top inserts, with two pilot holes marked from the board's width at those inserts.
- Pick the wall and the height you want the board at.
- Hold the board up and mark where its top inserts sit.
- Measure the board's width at the top inserts and mark the pilot holes from that measurement.
- Check the marks with a level.
- Drill, set the plugs or hit the stud, and screw the holders on.
- Set the board in and check that only the padded points touch it.
What do you do when the board comes off the wall?
Scrape the storage wax, check the edges, put the bindings back on at your stance, and start waxing every few days of riding.
- Scrape the storage coat off and brush the base.
- Look along both edges for rust. Buff light spots off with a gummy stone, and bring deeper rust in for an edge tune.
- Mount the bindings at the stance width and angles you wrote down in spring.
- Try your boots in the bindings and adjust the straps before your first day.
From there, wax every few days on the hill, or whenever the base looks dry or white, because firm made snow on Ontario hills wears wax off fast. If you changed boots over the summer, our snowboard boot sizing guide covers fit before you set the straps.
When the board comes off the wall, we can scrape the storage coat, tune the edges and remount your bindings at the stance width and angles you wrote down. Bring the board in when it comes off the wall if you'd rather not scrape and tune it at home.
Frequently asked questions
Can I lean the board in a closet in its bag instead?
Yes, as long as the board is waxed and dry first. Never Summer recommends closets and basements for off-season storage. Burton's storage guide says a dedicated board bag adds padding and keeps dust and bugs off stored gear. Stand it on its tail on a dry floor with the bindings off.
Will a wall mount fit a wide board?
A mount fits when its width range covers your board at the top inserts. Measure straight across the board at the top inserts and compare that number with the range listed for the mount before you buy. Measure the board you have rather than going by its model name.
Is it fine to hang the board in my room as decoration?
Yes, on a wall the window's sunlight doesn't reach and away from a radiator or heating vent. Direct sun and heat are what the storage advice above warns against. Wax it and take the bindings off first, same as any other wall.
So which wall setup should you go with?
We'd rather you hang a waxed, dry board with the bindings off on a padded vertical holder in a cool bedroom or closet than put it on any rack in a hot garage. The room and the wax decide how the board comes through summer. The mount's job is to hold it on padded points near the top inserts. A horizontal rack with padded arms is a fair second, and leaning it bagged in a closet works when there's no wall to drill.
Wax first: a thick coat over the base and edges, left unscraped until the board comes down. Pick up wax for a thick storage coat before the board goes on the wall, and grab a board bag too if it's headed for a closet. Then hang it somewhere cool and out of the sun, and leave it be until the hills open.
