A snowboard binding size chart matches the boot size you ride to a binding size, and binding brands publish their own charts. This guide puts two brands' charts side by side and shows where a US men's 10 and 10.5 land. It also covers Mondopoint sizing, women's boots, Step On bindings and the fit check to run once you strap in.
Find the size on your snowboard boot's label, then read it on the chart from the brand that makes the bindings you want. Each brand sets its own ranges, so the same boot can be a medium in one brand and a large in another. Before you buy, strap the boot in and check that the heel sits down, the boot is centred and both straps centre over the boot.
How do I read a snowboard binding size chart?

Find your boot size on the chart, then read off the binding size whose range covers it. Use the size printed on your snowboard boot, which can differ from your street shoe size. The charts in this post list US sizes and Mondopoint. Mondopoint is your foot length in centimetres, and it reads the same for men's and women's boots.
Each binding size covers a range of boot sizes, and some ranges overlap at the edges. Read only the chart from the brand that makes your bindings, since the boot brand doesn't set the binding size. If your boot label is hard to read, our guide to snowboard boot sizing converts US, UK, EU and cm.
Do size 10 boots need medium or large bindings?
A US men's 10 is a medium on Union's size guide and can be a medium or a large on Burton's size chart, and a 10.5 moves to a large on Union's chart while still sitting inside Burton's medium. The brand of binding decides which answer applies to you.
The full strap binding ranges sit side by side below, in US men's sizes and Mondopoint.
Pick the column for the brand you're buying and ignore the other. If your boot lands in two rows, the next section covers how to choose.
Should you size up or down between binding sizes?
Go up a size when the toe strap runs out of adjustment or the heel won't seat in the smaller size. Go down when the boot slides side to side in the larger size after you adjust the heelcup and straps. Trying both sizes with your own boots settles it.
Our read: the chart gets you to two sizes. Boots with the same US size can differ in outside length from one brand to the next, so the label is where you start and the strap-in check further down is where you finish.
What size bindings fit a women's boot?
Women's bindings use a women's chart in women's US sizes, so read your boot size straight across that chart. For a women's boot in a men's or unisex binding, use the Mondopoint number on the boot label. Match it to the Mondo column on that binding brand's chart. Mondopoint skips the conversion between men's and women's US sizes, so it is the cleaner number to read. If the label has no Mondo size, measure your foot length in centimetres.
How do Step On bindings size?
Step On bindings size on their own chart: Burton's size chart puts men's small at US 6 to 8, medium at 8.5 to 10.5, large at 11 to 13 and XL at 14 to 15, so a US men's 11 that fits a strap medium needs a Step On large. Burton also says Step On bindings only work with Step On boots, and warns that a mismatched size, or mixing men's and women's Step On gear, could compromise safety.
Use the Step On chart only for Step On gear. Match men's boots to men's bindings and women's boots to women's bindings.
How should bindings fit once you strap in?
The boot sits centred with the heel down in the heelcup, the toe strap centred over the toe and the ankle strap centred over the instep. Run these checks with the boots you'll ride:
-
Slide the boot in and kick your heel back into the heelcup.
-
Set the heelcup so the toe and heel hang over the board edges by about the same amount.
-
Buckle the ankle strap snug and move it until the pad sits centred over the instep.
-
Adjust the toe strap's length and position until it centres over the toe, with room left to tighten.
-
Flex forward and lean back. The heel should stay down, and the boot shouldn't slide side to side.
Bring the boots you'll ride when you buy bindings, and we'll run this strap-in check while we set your stance width and angles.
Does board length or width change your binding size?
No, binding size follows your boot, and the board's waist width decides how far that boot hangs over the edges. Board length is its own call, covered in our snowboard size chart guide.
With bindings mounted at your angles, look at the toe and heel from above. A boot that hangs well past both edges can drag in a hard turn. A wider waist or steeper binding angles fix that. A smaller binding won't, because the overhang comes from the boot.
Frequently asked questions
Are my bindings too big if there's a gap on each side of the boot?
Our read: only if the boot moves once it's strapped in. With the heel seated and both straps snug, rock your knee side to side. If the boot slides across the baseplate, reset the heelcup and straps. If it still slides, try the next size down.
Is a toe strap on its last hole a sign the bindings are too small?
Move the strap before you decide. Shift the toe strap's position and length so it centres over the toe, then tighten it again. If it can't centre on the boot with room left to tighten, try the next size up.
Will my boots fit a different brand's bindings?
Go by the binding brand's chart, then check the fit with your own boots. Union's size guide says its bindings fit all major boot brands, models and sizes, and calls its chart a guide to check against your specific boots. The strap-in check above is that check.
How do I tell what size my old bindings are?
Look under the baseplate first. Union prints the size on the bottom of most of its bindings, according to its FAQ. If there's no stamp, strap in the boots you plan to ride and run the fit check. A pair bought for old boots may not suit new ones.
Which binding size should you buy?
Buy the size your binding brand's chart gives for the boot you ride. When your boot lands in two sizes, take the one that passes the strap-in check. Buy in this order: boots, then bindings, then a board wide enough for those boots.
We'd rather you bring the boots when you shop for bindings, especially new boots this season. Strapping in before you pay shows you the heel, the straps and the overhang on the spot. If you're still choosing boots, our snowboard boot flex rating guide covers how stiff to go.
Size the bindings to the boots you'll ride, read only that binding brand's chart, and strap in before you commit. If you're buying on a budget this pre-season, browse our clearance bindings to size against your boots and check each pair on its own brand's chart.
Content courtesy of our friends at Union Binding Company
